 |
R70
Firm |
 |
| |
  |
|
 |
| 1/4" |
(6.35) |
|
|
|
3/8" |
(9.52) |
| 5/16" |
(7.93) |
|
|
|
|
|
|
R75
Extra Firm |
|
| |
  |
|
|
| 1/4" |
(6.35) |
|
|
|
3/8" |
(9.52) |
| 5/16" |
(7.93) |
|
|
|
|
|
|
13500
Sponged Cork |
|
| |
  |
|
|
| 3/16" |
(4.76) |
|
|
|
5/16" |
(7.93) |
| 1/4" |
(6.35) |
3/8" |
(9.52) |
| .28" |
(7.00) |
1/2" |
(12.70) |
|
|
|
|
|
C-85
Sponged Cork |
|
| |
|
|
|
| 3/16" |
(4.76) |
|
|
|
5/16" |
(7.93) |
| 1/4" |
(6.35) |
3/8" |
(9.52) |
| .28" |
(7.00) |
1/2" |
(12.70) |
|
|
|
|
1100
Soft |
|
| |
  |
|
|
| 1/4" |
(6.35) |
|
|
|
9/16" |
(14.28) |
| 5/16" |
(7.93) |
5/8" |
(15.78) |
| 3/8" |
(9.52) |
3/4" |
(19.05) |
| 7/16" |
(11.11) |
1" |
(25.40) |
| 1/2" |
(12.70) |
|
|
|
|
|
|
1700
Soft |
|
| |
  |
|
|
| 1/4" |
(6.35) |
|
|
|
3/8" |
(9.52) |
| 5/16" |
(7.93) |
|
|
|
|
|
| |
|
|
|
3500
Extra Firm |
|
| |
  |
|
|
| 1/8" |
(3.17) |
|
|
|
3/8" |
(9.52) |
| 3/16" |
(4.76) |
7/16" |
(11.11) |
| 1/4" |
(6.35) |
1/2" |
(12.70) |
| .28" |
(7.00) |
5/8" |
(15.87) |
| 5/16" |
(7.93) |
|
|
|
|
|
|
6500
Firm |
|
| |
  |
|
|
| 3/16" |
(4.76) |
|
|
|
7/16" |
(11.11) |
| 1/4" |
(6.35) |
1/2" |
(12.70) |
| .28" |
(7.00) |
9/16" |
(14.28) |
| 5/16" |
(7.93) |
5/8" |
(15.87) |
| 3/8" |
(9.52) |
|
|
|
|
|
|
2700
Medium |
|
| |
  |
|
|
| 1/8" |
(3.17) |
|
|
|
7/16" |
(11.11) |
| 3/16" |
(4.76) |
1/2" |
(12.70) |
| 1/4" |
(6.35) |
9/16" |
(14.28) |
| .28" |
(7.00) |
5/8" |
(15.87) |
| 5/16" |
(7.93) |
3/4" |
(19.05) |
| 3/8" |
(9.52) |
1" |
(25.40) |
|
|
|
| |
|
|
|
15700
Soft |
|
| |
  |
|
|
| 1/4" |
(6.35) |
|
|
|
3/4" |
(19.05) |
| 3/8" |
(9.52) |
1" |
(25.40) |
| 1/2" |
(12.70) |
|
|
|
|
|
|
14300
Firm |
|
| |
  |
|
|
| 3/8" |
(9.52) |
|
|
|
1/2" |
(12.70) |
| 7/16" |
(11.11) |
9/16" |
(14.28) |
|
|
|
|
| |
| |
Material Descriptions |
|
R-75 A very firm, low cost ejector for use on thin substrates.
Because of the wide thickness tolerance, it is recommended
for hand fed presses only. The firmness of this material can
quickly build up, top end tonnage. Caution should be used
so that the product being diecut isn't t damaged by compression
or that the press isn't overloaded. Recommended for flat diecutting. |
| R-70 Ditto the attributes of R-75 except for thicker substrates.
Recommended for hand fed flat diecutting where a wider variability
of rubber thickness is acceptable. |
| 13500
/ C-85 Sponged cork is an extra, extra firm material
that should be used sparingly because of the possibility of
tonnage overload. Recommended for flat diecutting in areas of
the die where you want to flat crush the substrate. (ie:Glue
Tabs) |
| 12300 A hard-to-beat, excellent ejector with very rapid recovery.
It is also very economical. Recommended for thick substrates.
Because of it's economy, it is attractive for hand fed flat
bed diecutting. Because of it's resiliency, it is a great ejector
for machine fed flat bed and rotary diecutting. It's resistance
to abrasion makes it an excellent ejector for cutting abrasive
products. See www.dieejection.com for more information on operation
range for this ejector. |
| 1100 An economical wider tolerance ejector for thick substrates.
Recommended for hand fed flat bed diecutting. |
| 1700 An economical wider tolerance ejector for thick substrates.
Recommended for hand fed flat bed diecutting. |
| 3500 A high quality, positive only tolerance, fast recovery ejector.
Gives a powerful quick ejection from a very small amount of
compression. Less top end loading for reduced pressure to cut
Excellent ejector for high speed presses cutting thinner substrates.
(up to .050' thick when using .375' thick ejector with a .063'
surplus over knife height) Recommended for flat diecutting.
See www.dieejection.com for more information on the operating
range for this ejector. |
| 6500 A kissing cousin of the 3500 but for thicker substrates. (Up
to .090' when using a .375' thick ejector with a .063' surplus
over knife height) Recommended for flat diecutting. |
| 2700 Related to the 3500 and 6500 materials with the same attributes
except for thicker substrates. (Up to .125' thick when using
a .375' thick ejector with a .063' surplus over knife height)
Recommended for flat diecutting. See www.dieejection.com for
more information on the operating range for this ejector. |
| 15700 Yet another relative of the 3500, 6500, 2700 family with the
same attributes except for thicker substrates. (Up to .165'
thick when using a .375' thick ejector with a .063' surplus
over knife height) Recommended for flat diecutting. See www.dieejection.com
for more information on the operating range for this ejector. |
| 14300 A firm ejector to be used on flat bed die cutters with thin
substrates. Best use is with hand-fed presses where wider variability
of ejector thickness is acceptable. |
|
